How Do You Replace A Piece Of Click Flooring?

Replacing a piece of click flooring is not difficult and doesn’t require any special skills or tools. The first step is removing the old piece using a jigsaw. 

Then, you’ll want to spread a thin bead of glue around the edges before replacing the new piece. You can use some clamps to hold it in place while it dries overnight. Afterward, remove them from the edges and wipe up excess glue with a damp cloth. 

Finally, place small nails in each corner to hold it in place as you work on the rest of your flooring project!

Replacing a Damaged Flooring Plank | Tips and Tricks
Takeaways
To replace a laminate floorboard in the middle of a floor, you will need to remove the damaged board, select a matching replacement board, and install the new board securely.
Always be careful when using power tools and make sure that you use safety glasses and gloves to protect yourself.
To ensure that the replacement plank is the right size, measure the damaged plank’s length, width, and thickness.
It is possible to replace a single damaged laminate plank without removing the baseboards, though it may require patience and skill.
If you want to replace a laminate plank with a different color or pattern, make sure to match it with the surrounding planks to ensure it doesn’t stand out or look out of place.

Cut Out The Damaged Piece Using A Jigsaw

If your damage is minor, you can cut out the damaged piece using a jigsaw. Just be sure to wear safety glasses and work on a sturdy surface such as a table or countertop. 

If you’re replacing an entire room’s worth of flooring, you can also use this method to remove the existing baseboards if they are not in good condition.

Once you’ve determined how much wood needs to be removed, mark out your lines with a chalk line and use a utility knife or scoring tool to make sure each line is straight and even before cutting it with your jigsaw (or miter saw). 

You’ll know when there’s enough room between the wall and the edge of your new piece because there will be screws sticking out from underneath; these should mark where your cut should go. 

Make sure that any cabinets or appliances are moved before starting so they won’t get accidentally damaged by falling debris!

Are you experiencing plumbing issues? Our comprehensive guide on fixing plumbing problems can help you address and fix any plumbing issues you may have. From identifying problems to solutions, we’ve got you covered.

Spread A Thin Bead Of Glue

To replace the damaged piece of click laminate, you’ll need:

  • A flooring adhesive
  • Scissors or a utility knife
  • A damp cloth to clean up any excess glue once it’s dried. You can use a paintbrush if you like.

Apply a thin bead of glue onto the back of your new laminate plank and place it in position along the edge where your old piece had been removed. 

If there are any gaps between the two pieces, use some glue to fill them before pressing firmly together so they stick properly. Don’t worry if some drips out on top (just wipe them off later).

Materials Needed to Replace a Damaged Piece of Click Laminate

Materials
Replacement click laminate
Tape measure
Utility knife
Pry bar
Hammer
Spacers
Wood glue or construction adhesive
Caulking gun
Toothpick or wooden dowel
Measuring square

Note: Before proceeding with the repair process, ensure that you’ve read the manufacturer’s instructions for your specific click laminate floor to avoid any damage or avoid invalidating the warranty.

Position The New Piece Of Laminate

Take your damaged piece of laminate, and cut it out with a jigsaw.

Spread a thin bead of glue all over the flooring, including around the edges.

Place the new piece on top of the glue, making sure that its edges are aligned with those of the original flooring (the joints in between should be flush).

Press down firmly for about 10 seconds to ensure that it is well stuck down; then clamp down all four sides using an old towel or other material to protect against scratching damage from clamps being placed directly onto your existing click flooring

Interested in learning more about roll flooring? Our informative article on what is roll flooring? explains the benefits of roll flooring and common types of floors available to suit your needs.

Align The Edges

Once you’ve got your flooring in place, align the edges of your new pieces with those of the existing Click flooring. This will ensure that everything looks seamless and no one can tell that there’s been an addition. 

You can use a tape measure to measure the distance between the existing flooring and the wall, then use it as a guide for marking out where to cut your new piece. 

If there is already complementary click moulded skirting around your room, measure this against both sides of each piece of click moulded skirting (there will be multiple pieces).

If you need to trim any edges after laying down your new click flooring pieces, use a straightedge or spirit level to check that they are perfectly straight before securing them in place using self-adhesive joints at regular intervals along each edge (these should come with your purchase).

Place Clamps On The Edges

Next, place clamps on the edges of your flooring.

These clamps will hold the laminate in place for about 30 minutes. After that time, remove the clamps and wipe up any excess glue with a damp cloth before it dries.

Want to know how to install roll-out flooring? Check out our guide on installing roll-out flooring, which provides an in-depth step-by-step process on how to install roll-out flooring to achieve a professional finish.

Press Down Firmly On The Flooring

Now that you have your replacement piece, you can use it to replace the damaged piece of click flooring. First, clear out any debris that’s in the way. 

Then, press down firmly on the flooring to ensure it’s secure and snug against the subfloor underneath. If your new flooring is still in its protective wrapper or packaging, do not cut off any excess laminate with a utility knife just yet; instead roll over it with a flooring roller so you don’t damage or scratch any surfaces.

Once all edges are in place and secured, use a jigsaw or circular saw to cut out any sections of old laminate around where the new piece will lay over top of those areas (without cutting through adjacent boards).

This is important so that when everything dries after application of adhesive for a seamless transition between floors! 

After removing these edges from old laminate if needed–and making sure all staples have been removed from underlayment–you can now begin applying adhesive around them using either pneumatic attachment tool like this one sold at Home Depot (note: please be sure not use too much pressure while using this type) 

OR by using roller applicator such as shown here sold at Amazon (note: be careful not apply too much pressure!).

Remove The Clamps After About 30 Minutes

After the clamps have been on for about 30 minutes, you can take them off. Don’t worry if you forget to remove the clamps; they won’t hurt anything. 

If you choose to leave them on for longer than 30 minutes, however, you should check periodically to see if they are damaging your flooring—if so, then use something like a rubber mallet or a hammer to gently pry up the clamp and remove it.

Searching for the perfect engineered hardwood flooring? Our article on how to buy engineered hardwood floors provides helpful tips on what to consider when buying hardwood floors, such as wood type, color, and finish.

Wipe Up Excess Glue With A Damp Cloth

First, wipe up excess glue with a damp cloth. DO NOT USE A WET CLOTH or a paper towel. You’ll need to wait 24 hours before you can use the flooring again, so it doesn’t make sense to create more work for yourself by needing to clean up messes that could have been avoided.

Tools and Materials Needed to Wipe Up Excess Glue

Tools/Materials
Damp cloth
Bucket of clean water
Rubber gloves
Sponges
Paper towels
Scraper or putty knife
Solvent or cleaner (if necessary)
Safety glasses

Note: Always wear protective gear such as gloves and safety glasses while cleaning up excess glue, as the solvent or cleaner used for cleaning may irritate the skin and eyes.

Place A Small Nail In Each Corner To Hold It In Place As You Work

First, you’ll want to place a small nail in each corner of your replacement piece and gently tap with a hammer until they are countersunk below the surface of the laminate. 

Then use a utility knife to cut off excess pieces along walls. Once everything is cut, unroll your new laminate underlayment and lay it on top of your flooring pieces.

Now that you have all of your materials ready and organized, it’s time to lay out everything so that you can easily keep track of where everything goes when you start filling in gaps between boards in order to prevent any missteps during installation!

Are you looking for places to buy vinyl plank flooring? Check out our article on where to buy vinyl plank flooring for recommendations on where to buy near you or online. From flooring stores to home improvement retailers, we’ve got you covered with our comprehensive guide.

Use A Hammer To Gently Tap With Nails Into Place Until Countersunk Below The Surface Of Laminate

Use a hammer to gently tap with nails into place until countersunk below the surface of laminate. Make sure the nails are not too long and that they are not visible from above. If you can’t see the head of the nail, it is not long enough.

Unroll Laminate Underlayment

The next step is to unroll the laminate underlayment. The underlayment should be laid down in the direction of the grain, so that it looks smooth and flat. 

It’s important to use a roller because this ensures that all of the seams are pressed together and will stay stuck together when you glue them down.

If you’re using a glue gun or another form of adhesive, apply it to both sides of each seam with a brush or paint roller before pressing them together with a squeegee or scraper (if using an adhesive).

Install From Left To Right, Pulling Back Overlapping Layer After Each Row

Install from left to right, pulling back overlapping layer after each row.

Do not install flooring in a room with no light (or very low light). A bright room is best for installing click flooring. You will have difficulty seeing the pattern and gaps in the click system.

Use a level to make sure your floor is flat before you start laying down any tiles or planks of click flooring. 

The tool should be able to detect any dips or bumps under your carpet or fabric covering on top of existing flooring material.

If you don’t have this type of tool, try using spirit levels as they are inexpensive and easy to use you can even build one yourself!

If you run into trouble with either level, contact us here at [company name] so that our customer care team can help troubleshoot how best put together your new space!

Use Utility Knife To Cut Off Excess Pieces Along Walls

After your main piece is in place, you’ll want to cut off any excess pieces along the walls. The key here is to use a utility knife and follow the pencil lines you drew earlier.

Once you’ve finished cutting, it’s time to lay down your border piece. You can use an adhesive or nail gun if you prefer just be sure that both types of fasteners are compatible with your flooring.

Replacing A Piece Of Click Flooring Is Not Difficult And Doesn’t Require Any Special Skills Or Tools

Replacing a piece of click flooring is not difficult and doesn’t require any special skills or tools.

Use a jigsaw to cut out the damaged piece. Be sure to wear eye protection, ear protection and heavy gloves.

Use a utility knife to cut off excess pieces along walls if necessary.

Spread a thin bead of glue along the top of the new laminate flooring and position it on top of your existing flooring with equal spacing between all edges (it’s important that all edges are aligned). 

Clamp down each edge using spring clamps or bar clamps until dry (usually overnight).

Conclusion

We hope that you’ve learned how to replace a piece of click flooring. The process is easy and doesn’t require any special skills or tools. With our detailed instructions, you’ll be able to do it yourself in no time

Further Reading

For additional information on replacing laminate floorboards, check out the following resources:

How to Replace a Laminate Floor Board in the Middle of a Floor: A detailed guide on how to replace a laminate floorboard in the middle of a floor with step-by-step instructions and images to guide you through the process.

How can I change a plank in the middle of the floor?: Pergo’s FAQ section provides useful and practical tips on how to change a plank in the middle of a floor, from selecting a replacement plank to installation and cutting instructions.

How to Replace Damaged Laminate Flooring Planks: A comprehensive article from Best Laminate that highlights the tools and techniques needed to replace damaged laminate flooring planks, including some do’s and don’ts to keep in mind.

FAQs

What tools do I need to replace a damaged laminate flooring plank?

To replace a damaged laminate flooring plank, you will need a circular saw, hammer, chisel, pull bar, and the appropriate replacement plank.

Is it possible to replace a single laminate plank in the middle of the floor?

Yes, it is possible to replace a single laminate plank in the middle of the floor. However, it will require some precision, especially when cutting the plank to fit precisely.

How do I measure the damaged plank to ensure that the replacement plank is the right size?

To measure a damaged plank, you need to measure its length, width, and thickness. Once you have these measurements, you can take them with you when selecting a replacement plank to ensure that you find the correct size.

Can I replace a laminate plank without removing the baseboards?

Yes, it is possible to replace a laminate plank without removing the baseboards. However, it will require some patience and skill, since you will need to remove the damaged plank and slide the replacement into place between the remaining planks and the baseboard.

Can I replace a laminate plank with a different color or pattern?

Yes, you can replace a laminate plank with a different color or pattern. However, you should be careful to match the color and pattern of the new plank to the surrounding planks, or else it will look mismatched and out of place.